EduTutor AI

Ray diagrams for mirrors and lenses that earn full marks

The two rays you always draw, the sign convention examiners insist on, and how to use the mirror and lens formulae without losing the minus signs.

Draw two rays, no more

To locate an image you only ever need two rays from the top of the object. Draw a third only if you want to check yourself.

For a concave mirror, use any two of these:

  • A ray parallel to the principal axis reflects through the focus.
  • A ray through the focus reflects parallel to the principal axis.
  • A ray through the centre of curvature reflects straight back along itself.

For a convex lens:

  • A ray parallel to the axis refracts through the focus on the far side.
  • A ray through the optical centre goes straight on, undeviated.
  • A ray through the focus on the near side emerges parallel to the axis.

Where the two reflected or refracted rays meet is the top of the image. If they do not meet but appear to come from a point behind the mirror or on the same side as the object, extend them backwards as dotted lines: the image is virtual.

The sign convention

This is where most marks are lost. Learn it once, apply it always.

  • All distances are measured from the pole of the mirror or the optical centre of the lens.
  • Distances measured in the direction of the incident light are positive; against it, negative.
  • Heights above the principal axis are positive; below, negative.

In practice, for the usual setup with light travelling left to right:

  • Object distance u is always negative — the object is on the left.
  • Focal length of a concave mirror is negative; of a convex mirror, positive.
  • Focal length of a convex lens is positive; of a concave lens, negative.
  • A real image on the left of a mirror has negative v; a real image on the right of a lens has positive v.

Write the signs into your "given" list before touching the formula. Almost every wrong answer in this chapter is a sign error, not an arithmetic one.

The formulae

Mirror formula: 1/v + 1/u = 1/f

Lens formula: 1/v − 1/u = 1/f

They differ by a sign, so check which one you are using. Magnification:

  • Mirror: m = −v/u = h'/h
  • Lens: m = v/u = h'/h

A negative m means the image is inverted and therefore real. A positive m means upright and virtual. Power of a lens is P = 1/f with f in metres, measured in dioptres.

The negative v tells you the image is on the same side as the object, which for a mirror means real. The negative h' tells you it is inverted. The signs are doing the work, which is why the convention matters.

Show answer

Given: u = −20 cm, f = +10 cm, h = +3 cm

1/v − 1/u = 1/f
1/v − 1/(−20) = 1/10
1/v + 1/20 = 1/10
1/v = 1/10 − 1/20 = 2/20 − 1/20 = 1/20

v = +20 cm — the image is 20 cm behind the lens, so it is real.

m = v/u = 20/(−20) = −1

h' = −1 × 3 = −3 cm, the same size as the object but inverted.

This is the special case where the object sits at 2F: the image forms at 2F on the other side, the same size and inverted.

The positions worth memorising for a concave mirror

Boards ask you to state the nature of the image for a given object position, often for one mark. Learn the pattern rather than re-deriving it:

  • Beyond C — image between C and F, real, inverted, diminished.
  • At C — image at C, real, inverted, same size.
  • Between C and F — image beyond C, real, inverted, enlarged.
  • At F — image at infinity, real, inverted, very much enlarged.
  • Between F and P — image behind the mirror, virtual, upright, enlarged.

The last one is why a concave mirror is used as a shaving or make-up mirror, and it is the only position giving a virtual image.

Small things that cost marks

No arrows on the rays. A ray diagram without direction arrows is incomplete; examiners deduct for it.

Not labelling F, C and the principal axis. Label them every time, even when you are short of time.

Writing the answer without its nature. "v = −30 cm" is half an answer. Say real or virtual, inverted or upright, and the size.

Dropping the minus on u. If u comes out positive in your working, you have already gone wrong, because the object is always in front.

Stuck on this in your own textbook?

Ask our tutor about this chapter and get an answer drawn from the book your board actually prescribes, with the passage cited.

Try a lesson free

More guides

EduTutor AI

Textbook-accurate tutoring for CBSE, ICSE and state board students, with every answer traced back to the chapter it came from.

© 2026 EduTutor AI. Written and maintained in India.